Magpul MIAD pistol grip

Trader rating · November 22nd, 2007, 08:33

I have read in several places that modifications are required to make these fit properly, and indeed, the one I purchased doesn't mate fully.

Although I've read frequently that modifications are required, I have yet to see any description of the modifications required. Could someone please assist me with this?

The symptom is, simply, that the pistol grip does not seem to cover the entire mechbox assembly. Someone said something about the bushing interfering.

No bullshit replies, please. If you know how to fix this or where the information lies, please let me know.

Jugglez · November 22nd, 2007, 08:49

It's going to vary a bit from one gearbox/body combo to another, generally you want to shave the inside of the grip, near the top. There's a track on each side of the grip that slide into grooves on each side of the gearbox. You want to shave those tracks down a bit.

Trader rating · November 22nd, 2007, 09:41

you mean shave them down at the TOP or the overall thickness? The grip slides on ok, but it seems to stop well before the end of the tracks in the mechbox.

Renegade) · November 22nd, 2007, 09:53

What kind of gun are you installing it on Morb? I had a problem with my Miad grip with my TM SR.. It appeared to go all the way on and straight, but no matter what I shaved off, that track, a little off the top, ect, I had motor allignment problems..

Trader rating · November 22nd, 2007, 10:16

It's going on a Hurricane Shrike

Jackals · November 22nd, 2007, 10:53

I got mine to fit on after shaving down the area inside the grip right where the bushings are. After I did that it worked fine.

leblanc74 · November 22nd, 2007, 18:15

will it fit a PTW?....I placed one into my hand this morning and it felt very good and ergonomics was excellent for me...but on the top there is one little hole for a bolt to go throught, do you trim off all the area?...

Mantelope · November 22nd, 2007, 18:23

Quote:

Originally Posted by leblanc74

will it fit a PTW?....I placed one into my hand this morning and it felt very good and ergonomics was excellent for me...but on the top there is one little hole for a bolt to go throught, do you trim off all the area?...

Only the real Tango Down one will, and only after many times as much dremelling as regular AS grips on regular AEGs require. However, it HAS been done, so it's not entirely impossible.

Omi-san · November 22nd, 2007, 19:08

Quote:

Originally Posted by Jackals

I got mine to fit on after shaving down the area inside the grip right where the bushings are. After I did that it worked fine.

+1

Installed on a TM M4A1 with Systema gearbox shell.

Trader rating · November 22nd, 2007, 19:18

FIXED. I'd appreciate it if a mod could change the title from "assistance required" to "FIXED" and/or move it to the solutions section.

Thanks to those who came to the rescue. Essentially, the issue is the insides of the pistol grip butting up against the bushing that just protrudes beneath the lower receiver (if your mechbox is so equipped).

The solutions is to dremel out grooves on both sides of the pistol grip, on the inside, about a quarter inch wide by an eighth of an inch deep so that the top of the grip will fit over the bushing and not interfere with it.

Slide the pistol grip on as far as it will go, and mark the section where the bushing comes into contact with the pistol grip using chalk. Remove the grip, dremel out the channels and the grip will go on no problem.

The channels don't need to go any farther down than the groove in the pistol grip.

Pictures coming later.

Thanks again guys!

Mantelope · November 22nd, 2007, 19:45

Quote:

Originally Posted by Mantelope

Only the real Tango Down one will, and only after many times as much dremelling as regular AS grips on regular AEGs require. However, it HAS been done, so it's not entirely impossible.

I'm on crack (or American turkey and beer) and I thought this thread was about the Tango Down battle grip. Whoops!

leblanc74 · December 1st, 2007, 15:14

Quote:

Originally Posted by Mantelope

I'm on crack (or American turkey and beer) and I thought this thread was about the Tango Down battle grip. Whoops!

No worries, I got one being custom made from a person in the US...Cannot wait to have my tangodown battle grip...

dodger_me · December 1st, 2007, 15:34

So does the airsoft version come with all the different customization parts like the real one?

eel one · December 1st, 2007, 16:33

Quote:

Originally Posted by dodger_me

So does the airsoft version come with all the different customization parts like the real one?

To make it short: No

dodger_me · December 1st, 2007, 17:32

does it come with any? or is it just like the picture on airsoftparts.ca

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

November 22nd, 2007, 08:33	#1
MadMorbius Guest Trader rating	Magpul MIAD pistol grip I have read in several places that modifications are required to make these fit properly, and indeed, the one I purchased doesn't mate fully. Although I've read frequently that modifications are required, I have yet to see any description of the modifications required. Could someone please assist me with this? The symptom is, simply, that the pistol grip does not seem to cover the entire mechbox assembly. Someone said something about the bushing interfering. No bullshit replies, please. If you know how to fix this or where the information lies, please let me know.

November 22nd, 2007, 08:49	#2
Jugglez Trader rating Join Date: Feb 2005 Location: Swimming in a pool of Xpresspost receipts.... Toronto - 400/401	It's going to vary a bit from one gearbox/body combo to another, generally you want to shave the inside of the grip, near the top. There's a track on each side of the grip that slide into grooves on each side of the gearbox. You want to shave those tracks down a bit. __________________

November 22nd, 2007, 09:53	#4
Renegade) A Total Bastard Trader rating Join Date: Apr 2006 Location: Tottenham, Ontario	What kind of gun are you installing it on Morb? I had a problem with my Miad grip with my TM SR.. It appeared to go all the way on and straight, but no matter what I shaved off, that track, a little off the top, ect, I had motor allignment problems.. __________________ W1-5

November 22nd, 2007, 09:41	#3
MadMorbius Guest Trader rating	you mean shave them down at the TOP or the overall thickness? The grip slides on ok, but it seems to stop well before the end of the tracks in the mechbox.

November 22nd, 2007, 10:16	#5
MadMorbius Guest Trader rating	It's going on a Hurricane Shrike

November 22nd, 2007, 10:53	#6
Jackals Trader rating Join Date: Sep 2004 Location: Ottawa. Ontario	I got mine to fit on after shaving down the area inside the grip right where the bushings are. After I did that it worked fine. __________________ Ottawa's Local Airsoft Site: www.ottawavalleyairsoft.ca

November 22nd, 2007, 18:15	#7
leblanc74 Trader rating Join Date: Oct 2007 Location: Coquitlam	will it fit a PTW?....I placed one into my hand this morning and it felt very good and ergonomics was excellent for me...but on the top there is one little hole for a bolt to go throught, do you trim off all the area?... __________________ My Collection: Seller/Buyer Feedback

November 22nd, 2007, 19:18	#10
MadMorbius Guest Trader rating	FIXED. I'd appreciate it if a mod could change the title from "assistance required" to "FIXED" and/or move it to the solutions section. Thanks to those who came to the rescue. Essentially, the issue is the insides of the pistol grip butting up against the bushing that just protrudes beneath the lower receiver (if your mechbox is so equipped). The solutions is to dremel out grooves on both sides of the pistol grip, on the inside, about a quarter inch wide by an eighth of an inch deep so that the top of the grip will fit over the bushing and not interfere with it. Slide the pistol grip on as far as it will go, and mark the section where the bushing comes into contact with the pistol grip using chalk. Remove the grip, dremel out the channels and the grip will go on no problem. The channels don't need to go any farther down than the groove in the pistol grip. Pictures coming later. Thanks again guys!

Magpul MIAD pistol grip

AEG Solutions