Crane stock that will fit ICS M4 with little work?

Death March · April 12th, 2006, 14:35

Thanks ERT,for the info! I think I'm going to take the whole back end apart though just so I don't have any metal shavings floating around inside.So I should be able to get at the adapter with a regular drill bit,I'm just going to have it all apart,I'm going to be adding other parts at the sametime anyway.Between Airsoft and my Mustang this is getting to be an $ month for me!Too many Hobbies.Thanks again for all that posted on this subject.

walks · April 14th, 2006, 06:56

dont forget you will need to grind down the side rails on the adaptor, it took me a few hours to get it the way I wanted it but it does work. also be sure to de-bur the hole you drill for the wiring

Death March · April 16th, 2006, 10:24

Thanks Field_gunner,I think I'm going to bevel the edge if I can't find some rubber to put around it.Thanks again guys!

Death March · May 3rd, 2006, 13:34

I would like to thank everyone again for the advice on this again,but I have one other question regarding the lone screw that goes up the Buffer tube,no one mentioned if they put that in?I,v done the set up,and you guys were not kidding about all the prob's in doing this little mod.But it's on there rock solid! I had too get a longer screw for the Buffer tube and used some (Permatex)Cold weld on the adapter.I found that I had to use the Long screw in the tube going into the upper Gear box,to make sure it was good to go.But everything else aside,it looks like it came with the gun.Thanks again guys.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

April 14th, 2006, 06:56	#17
walks Trader rating Join Date: Sep 2004 Location: Cambridge On	dont forget you will need to grind down the side rails on the adaptor, it took me a few hours to get it the way I wanted it but it does work. also be sure to de-bur the hole you drill for the wiring __________________

April 12th, 2006, 14:35	#16
Death March Trader rating Join Date: Feb 2006 Location: Manitoba	Thanks ERT,for the info! I think I'm going to take the whole back end apart though just so I don't have any metal shavings floating around inside.So I should be able to get at the adapter with a regular drill bit,I'm just going to have it all apart,I'm going to be adding other parts at the sametime anyway.Between Airsoft and my Mustang this is getting to be an $ month for me!Too many Hobbies.Thanks again for all that posted on this subject.

April 16th, 2006, 10:24	#18
Death March Trader rating Join Date: Feb 2006 Location: Manitoba	Thanks Field_gunner,I think I'm going to bevel the edge if I can't find some rubber to put around it.Thanks again guys!

May 3rd, 2006, 13:34	#19
Death March Trader rating Join Date: Feb 2006 Location: Manitoba	I would like to thank everyone again for the advice on this again,but I have one other question regarding the lone screw that goes up the Buffer tube,no one mentioned if they put that in?I,v done the set up,and you guys were not kidding about all the prob's in doing this little mod.But it's on there rock solid! I had too get a longer screw for the Buffer tube and used some (Permatex)Cold weld on the adapter.I found that I had to use the Long screw in the tube going into the upper Gear box,to make sure it was good to go.But everything else aside,it looks like it came with the gun.Thanks again guys.

Crane stock that will fit ICS M4 with little work?

Upgrades & Modifications